Dear DAVID Community,

In 2016, DAVID and this forum have been integrated into HP Inc.
This forum has been read-only since then, and will be switched off by then end of 2019.

To everyone who has contributed here, we thank you for all your work and for the constructive, helpful and friendly atmosphere you have created!
Please continue to discuss on the HP Support Forums.

STL-file from a MCT scan

STL-file from a MCT scan

Postby L.J.P.S » Mon Jan 14, 2013 8:18 pm

STL-file from a MCT scan (part1)

hello to all,
This is not a topic of scanning with David, but for me it's quite interresting enough to show. Some weeks ago a friend asked me some help in visualisation.
He is verry occupied in determinating insects that are included in "ambre" (fossilised resin of the Pinus succinifera) and he sent me the STL-file made from
the MCT-scan of this insect. MCT-scan stands for micro computertomography scanning and this scan was done at the UV Gent.
Notify that the insect is just somme 5 mm long.
His main objective for this scanning was to make a count of the number of induvidual eye cells of the compound eye. I dont know why, but the visualisation of this scanning was not verry handy for making the counting and finaly my frind decided to order a 3d print (fused deposit in a kind of ABS) This model could not resolve the problem of counting, unless he damaged it . Then he ordered a black model. The black one gave also no solution and it was more fragile then the lager white model.
Infact the surface of this in stl transformed scan is realy bad, it is verry "voxelised" , I would say: composed out of small cubes and it results in a hooking kind
(velcro-kind surface) of sanding paper.
As I allready said: he told me that the visualisation of this scanning was not very handy (visualisation and rendering was made in VGL).
They say that the transformation of those MCT-scannings to a STL-file is very complex and expencive.
But vieuwing this STL, I was verry disappointed about that "layered" and "voxelised" result.
I used in the first place David-software to visualise and separate the elements of the insect body.
(David Fusion is very handy and quick for such a job)
I put the separated compound eye in Blender, made a little sfere (the single eye bal), duplicated and posed it as many times as I needed.
I controled the placements and then I opend the "out-liner' where you can see the number of duplications. (infact realy simple, no hard job)
So job done in less then 1,1/2h and my frind could continue his description of the Insect and complete his article.
(for those who are interrested in the counting: 122 omattidia (tubed eye cells) for the left compound eye and 119 for the right . The
insect belongs to the Strepsiptera:

[courtesy Hans Henderickx , macro photography Hans Henderickx]

macro photo of the insect and a ventral vieuw MCTscan
macro photo, the green is the stl-file, the white and black are 3d-prints
Posts: 39
Joined: Wed Mar 11, 2009 5:37 am
Location: Belgium

Re: STL-file from a MCT scan

Postby L.J.P.S » Mon Jan 14, 2013 8:21 pm

STL-file from a MCT scan (part 2)
the haed and the compound eyes, a split-out and the placement of single sferes
some details showing the layered and cubic appeirance of the surface in STL
Posts: 39
Joined: Wed Mar 11, 2009 5:37 am
Location: Belgium

Re: STL-file from a MCT scan

Postby VDX » Mon Jan 14, 2013 9:16 pm

... impressive!

Posts: 260
Joined: Wed Jul 04, 2012 1:35 pm

Postby hal » Sat Jan 19, 2013 4:21 pm

Really an intersting job.
Thanks for sharing :D

User avatar
Posts: 1527
Joined: Thu Mar 01, 2007 4:08 pm
Location: Cavaria con Premezzo (VA), Italy.

Return to Hardware

Who is online

Users browsing this forum: No registered users and 1 guest